Printer Error 49 Fix

Printer Error 49 usually appears when you are attempting to print a document using a HP printer and then a communication failure error occurs between the computer and the printer. However, there are other probable causes for this message with an error 49 code to appear. There is a chance that it is related to the file that is being printed, or it could be due to a firmware problem. You must determine the cause of the problem and then fix the error to be able to make use of your printer again. This tutorial will guide you how to resolve printer error 49 on HP printers.

HP printer error 49 is typically caused by invalid print commands, damaged or corrupted data, invalid operations or sometimes registry issues. Some problems that can be easily fixed are caused by poor quality of the parallel cables that connect the printer to the computer. To stop the error messages from appearing, you must make sure that all possible causes are ruled out.

The way to fix HP printer error 49 is to first calibrate the printer. You can calibrate your printer by performing all these steps:

• Clear the print job from memory by pressing the Cancel Job command.
• Restart the printer by turning it off and on again.
• Print another job and this time from a different program.
• If the job printing was successful, return to the first application and print another file.
• If the error message shows up only with a specific software program or print job, contact the software vendor to get assistance from them.
• If the error message persists even with a different software application and print job, take off all the cables that connect the printer to the PC or the network and then turn off the printer.
• Open the printer and remove the entire set of memory DIMMS or third party DIMMS, but, DO NOT remove the firmware DIMM inserted in slot J1.
• Also, remove all the EIO devices from the computer.
• Turn on the printer again.
• If the error message does not appear again, then one by one return each of the DIMMS and EIO devices and turn the printer on and off each time you install a device.
• If you have pinpointed a specific device, replace it.
• Reconnect all the cables to hook the printer back up again to the computer or network.
• If the error code 49 still persists, replace the DIMM firmware.
• Lastly, replace the formatter of the printer and then calibrate the printer again.

After calibrating your HP printer, you have to make sure that your Windows registry is free from errors. The registry is an important component of Windows that stores all file and program settings that allow your operating system remember to load and use the different programs on your PC. Despite its significance in your system, it can be affected by the constant use it inevitably undergoes. You need to resolve registry issues by using a reliable registry cleaner that can thoroughly clean your registry. We highly recommend that you make use of "Frontline Registry Cleaner", which can resolve 99% of system faults found in your system, allowing you to use your computer in its optimal condition.

Source:- Ezinearticles.com

Read More

Fix Printer Spooler Error

Your about to print an important document that you need for work or school and as you hit that print button, a windows error that says "Operation could not be completed. The print spooler service is not running". What to do now? Well here are a couple tricks that will fix this problem.

Instructions

1. Click on Start then click on Run. In the dialog box type services.msc and click OK, this will bring the services window up. Scroll down to print spooler, of course just turning it on wont fix it but we do want to make sure that the start up type set to automatic. double click on the Print Spooler Service and set start up type to Automatic, then click OK.

2. Restart the machine. Then once the machine is back up reinstall the software that came with the printer. If you don't have it you can always go to the vendors website and download it.

3. If that doesn't fix the problem we are going to want to completely uninstall all the software for the printer and reinstall it. So click on Start then Run type Control Panel in the dialog box and click OK. Click on add remove programs and uninstall the software for the printer.

Then check Under the Printer and Fax to see if it was uninstalled. If not then just delete it. Printer and Fax is in the Control Panel. Once it is completely uninstalled reinstall the software for the printer.

4. Then check Under the Printer and Fax to see if it was uninstalled. If not then just delete it. Printer and Fax is in the Control Panel.

Read more: eHow.com

Read More

Fix Lexmark Printer Errors

If your Lexmark inkjet or laser printer is printing erratically, printing incorrect colors or not functioning at all, you don't need to return the unit or find a service center for a repair immediately. There are a series of simple troubleshooting steps you can follow at home to fix the printer on your own.

Instructions

1. Check to make sure the printer's AC adapter is firmly plugged into a wall outlet and its USB cable is connected to the USB port on your computer. Try plugging the AC adapter into a different wall outlet, in case your outlet has stopped working or try a different USB cable in the event that it has gone bad. Pop open the top cover of the printer and check to see if any paper is jammed inside and needs to be physically removed.

2. Open the plastic cover over the ink cartridges or laser toner and pull them out. Check the orientation of the ink or toner. Replace them to make sure they are properly installed. Snap the plastic cover back into place.

3. Read the information on the LCD screen that shows the printer's status if you have a Lexmark laser printer. Check to see if there is a specific error message being displayed and then consult your manual to see what steps can be taken to fix the problem. Take the printer to a Lexmark authorized service center or purchase your own maintenance kit and replace the print head if you see the error message "Error 80 Scheduled Maintenance" (see Resources below). Remove and then return the toner cartridge if you see the error message "Error 20." Replace the cartridge entirely if you see the error message "Error 31," which indicates a defective cartridge.

4. Power your computer off and then back on. Attempt to print your document again in case your computer stopped recognizing your printer temporarily. Click "Start" on your task bar and then access the Control Panel. Choose the option to "Remove Programs." Uninstall the Lexmark software you installed when you first setup your printer. Locate the CD or floppy disk that came with your printer and put it in your computer. Follow the instructions on the screen to re-install the software.

5. Access the Control Panel again. Click "Printers." Verify that your Lexmark printer is in the list of available printers. Click "Add a Printer" if your printer is not showing up. Follow the instructions to add your printer. Navigate back to the Control Panel and click "Devices." Click on the plus sign next to "Printer" and then right-click on the name of your printer. Click "Settings" and then click "Drivers." Download the new software if a more up-to-date driver is available.

6. Open the Lexmark printer software by double-clicking on its desktop icon or navigating to it through the Start bar. Click on the option to print a test alignment page to ensure that your printer is now working properly.


Read more: eHow.com

Read More

Fix 0x0000007E Printer Error

SYMPTOMS
After you upgrade your computer to Windows XP, you might receive the following S...
After you upgrade your computer to Windows XP, you might receive the following Stop error message when the computer starts:
STOP: 0x0000007E (0xC0000005, 0x804E518E, 0xFC938104, 0xFC937E04)
SYSTEM_THREAD_EXCEPTION_NOT_HANDLED

WUSB54GCx86.sys- Address 92D89498 base at 92D7c000, Datestamp 45c04cc9
Note The parameters and file names in this error message might vary, depending on the cause of the Stop error. The file name in the second line of the error message, WUSB54GCx86.sys, is an example of a driver file that might be causing the error.

This article discusses seven methods for resolving the problem. The first method is designed for beginning to intermediate computer users. The other six methods are designed for advanced computer users.

Because this article contains steps that involve restarting your computer, you might find it easier to follow the steps if you print this article first.

CAUSE
This issue might occur if a system thread generates an exception that the error...
This issue might occur if a system thread generates an exception that the error handler does not catch. This exception can be caused by any of the following:

* If this issue occurs after the first restart during Windows Setup or after Setup is complete, the computer might not have sufficient hard disk space to run Windows XP.
* The computer BIOS might be incompatible with Windows XP, or it might have to be updated.
* The video adapter drivers might be incompatible with Windows XP.
* A device driver or a system service might be damaged.
* If the issue is associated with the Win32k.sys file, it might be caused by a third-party remote control program.


RESOLUTION
Use the Windows Error Reporting tool You can use the Windows Error Reporting to...
Use the Windows Error Reporting tool
You can use the Windows Error Reporting tool to send information about the error to us and to obtain information about any available fix or workaround. Follow these steps to use the Windows Error Reporting Tool:

1. When the Windows Error Reporting window pops up on your computer, click Send Error Report to send the error report to us.
2. In the confirmation window that appears after you send the error report to us, click More Information. This helps you find any available fixes for the problem or information about how to work around the issue.
3. If a fix or a workaround is not available, you can use the "Advanced Troubleshooting" section to try to resolve this issue. If you are not comfortable with advanced troubleshooting, you might want to contact Support. For information about how to contact Support, visit the following Microsoft Web site:
http://support.microsoft.com/contactus/ (http://support.microsoft.com/contactus/)


Advanced troubleshooting
Use the following methods in the order in which they are presented.

Method 1: Make sure that you have sufficient hard disk space
First, make sure that you have sufficient hard disk space. The Stop error can be caused by insufficient hard disk space.

If you can use safe mode or the Recovery Console to start the computer, delete any unnecessary temporary files, Internet cache files, program backup files, and files that contain saved file fragments from disk scans (.chk files). You can also install Windows XP on another hard disk that has more free space.

If you cannot start the computer, go to the next method to update the computer BIOS.

For more information about safe mode or the Recovery Console, click the following article numbers to view the articles in the Microsoft Knowledge Base:
315222 (http://support.microsoft.com/kb/315222/ ) A description of the Safe Boot Mode options in Windows XP
314058 (http://support.microsoft.com/kb/314058/ ) Description of the Windows XP Recovery Console

Method 2: Update the computer BIOS
If freeing space on your hard disk did not resolve the problem, the BIOS might have to be updated. Use the hardware and software vendor contact information articles that are listed in the "References" section to contact the computer manufacturer to obtain the most recent BIOS update.

Note When you update the BIOS, you might have to disable BIOS memory options, such as caching or shadowing, temporarily.
Method 3: Disable or update device drivers
If you have updated the BIOS successfully and the problem persists, the video adapter drivers on the computer might have to be updated or disabled. Follow these steps to troubleshoot the video adapter drivers:

1. If a driver is listed by name in the Stop error message, disable or remove that driver.
* If the error occurs during the startup sequence and the system partition uses the NTFS file system, you might be able to use safe mode to rename or to delete the faulty driver.
* If the driver is used as part of the system startup process in safe mode, you must use the Recovery Console to start the computer.
2. If the Stop error message does not indicate a specific driver, update the video adapter drivers to the latest versions.
3. Disable or remove any drivers or services that you recently added.
4. Check the Microsoft Hardware Compatibility List (HCL) to determine whether the PCI devices in the computer are compatible with Windows XP. For information about the HCL, visit the following Microsoft Web site:
http://www.microsoft.com/whdc/hcl/default.mspx (http://www.microsoft.com/whdc/hcl/default.mspx)

Method 4: Remove unsigned drivers
If you have updated the video adapter drivers and the problem persists, or if you cannot start Windows in safe mode, the problem might be caused by a different, unsigned driver. Remove all drivers that are not digitally signed by Microsoft. For more information about how to do this, click the following article number to view the article in the Microsoft Knowledge Base:
316434 (http://support.microsoft.com/kb/316434/ ) How to perform advanced clean-boot troubleshooting in Windows XP

Method 5: Remove all third-party drivers
You might be unable to determine which third-party driver causes the error. If removing unsigned drivers does not resolve the issue, try moving all third-party driver files from the %Windir%\System32\Drivers folder to a different location. Follow these steps to move the third-party driver files:

1. Use the Recovery Console to start the computer, or start the computer from a different installation of Windows if you have performed a parallel Windows installation.
2. Create a temporary folder to hold the driver files. For example, you could create c:\DriverTemp.
3. Move all files that do not have a creation date for Windows XP of 8/13/2001 from the %Windir%\System32\Drivers folder into the temporary folder that you created in step 2.

Caution If the computer relies on third-party IDE or SCSI controller drivers for correct operation, you must identify those driver files and then leave them in the %Windir%\System32\Drivers folder.
4. Restart the computer.
5. Continue the Windows Setup program. You can add the driver files back to the computer one at a time to identify the faulty driver.

Method 6: Remove third-party remote control services

If you still have the problem after you use the previous methods and the Stop error message contains the Win32k.sys file name instead of a driver file name, the problem might be caused by a third-party remote control program. To remove the service, use the Recovery Console to start the computer and then delete the third-party remote control service file.



 Source:- support.microsoft.com

Read More

Fix 0x00000050 Error Message on HP Printer Drivers

SYMPTOMS

When you use Hewlett-Packard (HP) printer drivers, you may receive a "STOP 0x00...
When you use Hewlett-Packard (HP) printer drivers, you may receive a "STOP 0x0000000a" or a "STOP 0x00000050" error message on a blue screen.

Note This issue has been known to occur with HP 4500, HP 8000, and HP 8001 drivers.

CAUSE

This issue occurs because the drivers are incompatible with Windows NT 4.0....
This issue occurs because the drivers are incompatible with Windows NT 4.0.

RESOLUTION
To resolve this issue:Remove or update your HP printer drivers. For additional...
To resolve this issue:

1. Remove or update your HP printer drivers. For additional information, contact HP support.

Test to determine whether the issue is resolved. If the issue is resolved, skip the remaining step. If the issue is not resolved, go to step 2.
2. Apply the hotfix that is described in Microsoft Knowledge Base article number 811493. Click the following article number to view this article in the Microsoft Knowledge Base:
811493 (http://support.microsoft.com/kb/811493/ ) MS03-013: Buffer Overrun in Windows Kernel Message Handling Could Lead to Elevated Privileges



Source:- http://support.microsoft.com/

Read More

Fix Printer Runtime Error 482

Runtime error 482 is an error caused when you try and use various printer functions inside your Windows computer. The most common cause of these errors is either from having damaged system files inside your PC or from a variety of different errors that can cause your computer to run unreliably. You can fix this error very easily by using the steps in this article to cure any of the issues that cause it to occur...



The Runtime 482 error normally shows in this format:

* Run-time error '482′: Printer Error
* Printer Error

The error is specifically caused by the "PrintForm" command inside Windows becoming damaged and corrupted. This command is used widely in software programs to print the files that you want, but is prone to a lot of damage, leading your system to become unable to use it - showing the Runtime 482 error.

The first thing you can do to avoid this error is to avoid using "printform". This is an in-built Windows command, but ca be circumvented by using the likes of "EndDoc" before it. This is very important as it allows your software to print the documents you want without showing the Runtime 482 error.

After you've done that, it's advisable that you clean out the registry with a "registry cleaner". The registry is often the cause of Runtime errors because of the way it's continually being used by your computer. Every day, the registry is being opened and read to help your system recall a huge number of settings and options. Everything from your desktop wallpaper to your most recent emails are kept in the registry database, making it one of the most important and frequently used parts of your PC. Unfortunately, the registry is also causes the Runtime 482 error, as it's often damaging many of the settings that your printer requires to run. To fix this problem, you need to use a 'registry cleaner' to repair any of the damaged registry settings inside your PC, allowing your computer to run much faster and smoother.



Source:- ezinearticles.com

Read More

Fix Samsung Printer Error Codes

There have been several models of the Samsung Laser Printer released into the market. However, many of them seem to pose various degrees of problems. Here are some of the common error codes along with tips on troubleshooting:

Error message: Scanning error

This error message is essentially a hardware error. You could try to replace the USB cable. Sometimes poor quality cables cannot transmit the large data needed by a scanner.

Error message: paper jam

This happens when the paper has got stuck in your Samsung Laser Printer. You need to check the sensor located beside exit rollers. Maybe it is in incorrect position, or is damaged. If nothing works, try replacing it with a new sensor.


Error message: square prints

Sometimes you may experience that your Samsung Laser Printer is printing out squares instead of regular text. It can happen if you are using Firefox or printing content from sites which do not recognize the font used in the text. To fix this problem you will need to reinstall all relevant drivers. If this doesn’t help then visit the printers and faxes folder, select your printer and choose the properties.

Error message: missing print

Sometimes, a portion of your page could be devoid of print. It can happen because of incorrect paper size configuration. Check the settings and try again.

Error code: H2

This error code indicates that there is a problem with the fuser warming up. Make sure all the cables are in connection and that no point is missing.

Error message: Media tray empty

Sometimes even if the tray is loaded with paper you could be getting this error message on your Samsung Laser Printer. Try updating the drivers by visiting the Samsung site. This should rectify issues.

Error: Toner light still on

After replacement of the toner cartridge you might still find the toner light switched on continually. You need to check on the fuse located on the front side of the cartridge. You could try replacing this with a 50 mp one. This error usually occurs in the Samsung SCX-4216F.

Error code: 24

This error code indicates that there is too much overload as far as the print job is concerned. You can select the button called ‘continue’ and then try reducing the amount of print job.

Error code: 50

This indicates a malfunction in the fuser. It means the fuser is not heating up. Try switching off your Samsung Laser Printer or resetting the printer for around 15 minutes and then switch it on again. In case this does not solve the problem, it could indicate a fault in the fuser assembly or in the AC power.

Error code: 16

This error code means that the toner is low. That means the distribution of the toner inside the cartridge is inadequate. You need to take out the cartridge and move it back and front gently. If this does not work try replacing the cartridge. You could also try cleaning up the contacts.



Source:- errorbank.com

Read More

Fix HP Printer Print Blank Pages Error

Is your printer printing blank pages? Don’t be surprised! This is not a surprising occurrence. This is a problem that you might face from time to time.

STEP 1: Clean Print Head

The print head gets clogged due to frequent usage. Therefore, the ink will not be able to get out of the cartridge. Hence, the printer only prints blank pages. The solution to this problem will be to clean the print head. This can be done by cleaning it with a damp cloth or with an Iso Propyl Solution.

STEP2: Check if Cartridge is Empty

If this does not work, your next step would be to check if there is any ink in the printer cartridge. You might be giving a command for a high resolution printout, but the ink might not be enough for such a purpose. Look out for the printer prompts that will tell you about the low levels of ink.

STEP 3: Install the Correct Printer Driver

Many a times if you are downloading a printer driver from the internet, you might download the wrong driver. This will result in the computer not recognizing the printer. The result is blank pages.

STEP 4: Check for Appropriate Paper Size

Another facet to be taken care of is the printer size. You must check the Page Setup Dialog box whether you have selected the settings that are in tune with the paper size that is being used for the printing.

STEP 5: Check the Operations

If nothing works for you, then a printer operations checks is in order.



Source:- printerinkcartridges.printcountry.com

Read More

Error 0x00000643 When Installing a Wireless Printer

This happens when Windows is able to detect the Wireless port for the Printer but not the Printer itself.
Follow the below mentioned steps to solve this problems,
Intstall the Printer again but with the Standard Drivers

• Now that the new printer is seen under Add Printers and Faxes window, then delete the Wireless Printer which you had installed earlier
• Reboot the Computer 3 times (This is to remove all the installed components and unregister all at the same time)
• Now install the Wireless Printer again with the original set of the drivers which came with the Wireless Printer
• Turn on the Printer and Restart the Computer

Source:- errorsnsolutions.com

Read More

Top 10 HP printing problems and how to fix them

While they're generally very reliable, even in the most demanding of environments, HP printers are still problematic from time to time. And we all know printers fail at the most inopportune moments. For an IT support professional, it's critical to know how to fix the most common problems associated with these printers. I've identified 10 problems you can expect to run into most often when dealing with an HP printer, and I've included suggestions on fixing them.

1. Paper jams
Among the most common problems with any make of printer are paper jams. A printer will jam for any number of reasons: It’s dirty, the wrong paper type is being used, or the rollers on the printer that feed the paper through its pathway are worn down. While cleaning the printer periodically and using the correct paper type are easy fixes, roller replacement can be a difficult job depending on the model of HP printer. For some HP printers, the rollers are easily accessible, but you'll need to completely tear down other models to remove the rollers. Regardless of the cause, when removing a paper jam, always pull the paper in the direction of the paper path, because pulling it backwards can severely damage the printer.

Certain HP printers are more susceptible to paper jams than others. In my experience, any printer that holds the paper vertically and then pulls it down through the printer invariably ends up having paper jam problems. These models aren't designed for heavy use, but many organizations make use of them on individual systems and should be aware of this flaw. In addition, some people have trouble with the newer HP 4000 series printers' paper pickup rollers—which is odd, because the older 4000 and 5000 series HP printers are considered rock solid and don't seem to have any trouble with their pickup rollers.

2. Some or all of the printing on the page is faded
A faded print image is normally the result of one of three conditions: The printer is getting low on toner, the print density is set too low, or Economode printing is turned on. For the last two settings, a printer self-test (typically a separate button on the printer) will show what the current settings are. If Economode is on, and users are complaining about how light the print is, turn it off and/or set the print density higher. If the toner is low, simply removing the cartridge and shaking it to redistribute the toner more evenly can temporarily resolve the problem until you can replace the cartridge.

3. Ghosting
Ghosting is a condition where the image prints properly, but a much lighter copy of the image also prints elsewhere. This can be due to a problem with the power outlet that is supplying power to the printer. Check the power outlet by plugging in a different printer to see if the same results occur. Ghosting can also be caused when consumable printer parts (such as the drum or imaging kit) are near the end of their life. All of the consumable parts in a printer are rated for a certain number of pages. Once a printer gets near that magic number, you'll need to replace those parts to eliminate ghosting.

4. Toner smears or does not stay on the paper
If words and images come off the paper when a hand is run across them, there are a few possible problems. First, the fuser assembly may be damaged or at the end of its life. The solution is to replace the fuser assembly. Repairing a fuser assembly is generally not recommended because the fuser is considered a consumable printer part and not worth the time or effort to fix. Second, the toner cartridge may be defective and letting too much toner out at one time. In a black-and-white laser printer, the solution is to replace the toner cartridge. In a color laser printer, only replace the cartridge that is exhibiting the problem. Third, some toner may have spilled in the printer. If so, you'll need to clean it out.

5. Printer is displaying a 50.4 error message
A 50.4 error message on some of the newer HP LaserJet printers indicates a problem with the power supply. If the printer is connected to a UPS, disconnect it, or disconnect it from a power strip and plug it directly into a wall outlet. A laser printer should never be plugged into a UPS, because the UPS can be damaged by the surges of power required by a printer to keep the fuser assembly warm. If that doesn’t work, make sure that all of the components in the printer are seated properly.

6. Can't find a driver for a particular operating system
As new operating systems are released, new drivers will need to be loaded for your existing printers. Not all printers have a driver for every OS. In these cases, it’s best to consult the printer manual and find out what printers the drivers will emulate. While not all of the functionality of the printer will be available under this emulation, at least basic printing will work. For example, most HP printers will print with the HP LaserJet II driver installed, although specific options, such as duplexing, will not work.

7. Printer is not printing from the expected paper tray
Look in two places to correct this particular error. First, look on the printing PC, and second, on the printer. If the application is set to print to the wrong paper tray, correct it within the application by clicking on Printer Properties and finding the Tray Selection source. On the printer, make sure that the paper sizes in the control panel match what is actually in the paper trays.

8. Printer picks up all the paper from the manual feed tray rather than one sheet
The pad that is responsible for separating the paper has likely worn out and needs to be replaced. You can order and install a new pad without sending the printer out for repair. It is also possible that the paper is wet due to humidity. Make sure the paper is properly stored and that it is “fanned” before putting it into the printer.

9. Printer is displaying a 79 error
A 79 error can be the result of a problem with the network print server that services the printer. When troubleshooting a 79 error, first open the Printer folder from the Start menu on the Print server to make sure there are no jobs pending. A 79 error can also indicate a failure of a printer add-on component, such as an MIO card or a RAM module. All add-ons should be removed and then added back to the printer one by one to determine which module may be at fault.

10. Trouble printing onto envelopes
Envelopes can cause many problems for laser printers. Choose envelopes that are close to 20-lb paper in weight and thickness. Also, make sure that the adhesive on the envelope is capable of withstanding the heat that the fuser puts out to keep the printing on the page. If you don’t, the envelopes will come out of the printer already sealed. If envelopes are coming out of the printer wrinkled, they may be too stiff for the paper path. Open the rear of the printer and let them exit at that location instead.



Source:- articles.techrepublic.com

Read More

WINXP-PRO ADD PRINTER INSTALL ERROR

Tech Advise:1

Click On Start Menu >> Click On control panel admin tools >> services
Or run services.msc in RUN command line
Look for service named Print Spooler and make sure it's started.

Tech Advise:2

Please do the following steps

Step:1

Start the computer in safe mode
Start the computer in safe mode in order to remove spool files.

Please do the follow these steps:

Restart your computer and press the F8 key repeatedly while the computer is starting.
On a computer that is configured to run multiple operating systems press the F8 key when the Boot menu appears.
Select Safe Mode when the Windows Advanced Options menu appears and then press ENTER.
If the Boot menu appears again and you are prompted to select an operating system use the arrow keys to select the operating system and then press ENTER.


Step:2

Delete the spool printer and driver files
In safe mode delete the spool printer and driver files.
To do this start Microsoft Windows Explorer and then delete all the files and the folders in the following two folders where C: is the drive where Windows XP is installed

C:\Windows\System32\Spool\Printers
C:\Windows\System32\Spool\Drivers\w32x86


Step:3

Edit the registry

Warning Serious problems might occur if you modify the registry incorrectly by using Registry Editor or by using another method.
These problems might require that you reinstall the operating system.
Microsoft cannot guarantee that these problems can be solved.
Modify the registry at your own risk.
First remove the Windows NT subkeys
Remove the potentially problematic registry entries for Windows NT x86 service subkeys.
These may have been installed by third-party printer setup programs and may be interfering with the print spool service.
Follow these steps to keep the drivers print spools and registry entries that were included with Windows and to remove all other drivers print spools
And registry entries that may be causing issues.

Start Registry Editor.
To do this
Click Start>>click Run
Type regedit in the Open box and then click OK.
Locate and expand the following registry key to view the list of subkeys subfolders
HKEY_LOCAL_MACHINE>>>SYSTEM>>>CurrentControlSet>>>Control>>>Print>>>Environments>>>Windows NT x86
In the subkey list, there should only be the following subkeys:
Drivers
Print Processors
If there are any subkeys other than the subkeys that are listed in step 2
Follow these steps:
On the File menu >> click Export.
In the File Name box
Type the name that you want to use for this key such as WindowsNTx86regkey and then click Save.

You can use this backup of the HKEY_LOCAL_MACHINE>>>SYSTEM>>>CurrentControlSet>>>Control>>>Print>>>Environments>>>Windows NT x86 registry key to restore the key if you experience any issues after you complete this procedure.
Delete all the subkeys other than the subkeys that are listed in step 2.
To do this right-click each subkey that is not displayed on the list and then click Delete.
Click Yes when you are prompted to confirm the deletion.

Second remove registry entries for the default print monitors
Remove the potentially problematic print monitor subkeys that may be interfering with the printer that you want to use.
These may have been installed by third-party printer setup programs.
Follow these steps to keep the print monitors and registry entries that were included with Windows and to remove all other print monitors and registry entries that may be causing issues.



Start Registry Editor if it is not already open.
Please do this
click on Start Menu >> click Run
Type regedit in the Open box and then click OK.
Locate and then expand the following registry key to view the list of subkeys
HKEY_LOCAL_MACHINE>>>SYSTEM>>>CurrentControlSet>>>Control>>>Print>>>Monitors
In the list of subkeys there should only be the following subkeys for the default print monitors
BJ Language Monitor
Local Port
PJL Language Monitor
Standard TCP/IP Port
USB Monitor
If there are any subkeys other than the subkeys that are listed in step 2 follow these steps:
On the File menu click Export.
In the File Name box type the name that you want to use for this key such as Monitorsx86regkey and then click Save.
You can use this backup of the HKEY_LOCAL_MACHINE>>>SYSTEM>>>CurrentControlSet>>>Control>>>Print>>>Monitors registry key to restore the key if you experience any issues after you complete this procedure.
Delete all the subkeys other than the subkeys that are listed in step 2.
To do this right-click each subkey that is not displayed on the list and then click Delete.
Click Yes when you are prompted to confirm the deletion.
Exit Registry Editor.
If a printer is attached to the computer disconnect the printer cable from the computer and then restart the computer.


Step:4

Install the printer and print a test page
Reconnect the printer cable to the computer
Install the printer according to the manufacturer’s instructions and then try to print a test page.



Source:- techmowgli.com

Read More

Canon PIXMA Multifunction printers

On the other hand, Canon PIXMA multifunction printers do not have the advanced features that the Brother MFC multifunction printers have. They are as versatile as can be expected from multifunction printers, but the features that Canon PIXMA multifunction printers possess are just basic, good for small working environments.

For one, many models only have basic fax functions. Some cannot print from or even read USB flash drives. Some cannot function as photo printers.

Eventually, what it all comes down to is what exactly do people with home offices need in multifunction printers. If they want multifarious functions and features in a printer, and if their printing needs demand versatility in a printer, they should go for Brother MFC models. However, if they are not that big on features and functions and are more focused on printing output quality, a Canon PIXMA model would be a better choice for them.

Read more: articlesbase.com

Read More