A Tip For Solving Most Printer Errors

Ever have blinking lights on your inkjet or laser printer that just will not go away? Ever install a new ink cartridge in your printer and it still thinks the old one is there? Well, instead of just getting angry at the printer or hunting around for your manual, you can try one simple thing: unplug it.

This technique has a few names that all mean the same thing: cycling the printer, resetting the printer or clearing the printer’s memory. Now unplugging your printer may seem like a low-tech solution to complex problems, and in reality it is. But, for problems like blinking error lights it is the only solution and also, it is typically the first one that will be recommended to you by a technician working for HP, Lexmark, Epson etc. They will recommend it right away if you install a new cartridge and it is registering as empty. If your printer isn’t registering it full, then that means it still thinks the old cartridge is in there and the memory needs to be cleared by unplugging it.

The first thing to remember about this solution is that unplugging the printer is not the same as turning the printer off. If you have error messages or cartridge communication problems, then turning off the printer is not going to do anything. It has to be physically unplugged from the wall or the back of the printer itself (you don’t have to unplug the printer from the computer). The second and most important thing is that the printer must be unplugged for at least one minute. It takes at least one minute for all the electricity to be cut off from the printer to allow it to completely reset and clear its memory. If you just unplug it for a few seconds, when it comes back on it is going to pick up right where it left off.

While this technique will not fix every problem, it is still a very quick and easy solution to a lot of annoying printer problems and it is always the best place to start when one of those problems arises.

Article Source: http://www.articledashboard.com/Article/A-Tip-For-Solving-Most-Printer-Errors/19781

Read More

Printer Error - Steps To Repair The 482 Error On Your PC

The Runtime 482 "Printer Error" is a common problem for many Windows computers. The issue is caused by the way in which your computer cannot properly read the printer settings / configuration on your system, which will prevent your PC from being able to load up the files it requires to print out a document for you. Although this error may seem tough to fix, the good news is that you can cure it pretty easily if you're able to repair the various files & settings which cause it in the first place.

The error you're seeing will generally show in this format:

Run-time error ‘482′: Printer Error or Printer Error

There are a number of reasons for this Runtime 482 error to show, from having the incorrect Printer Drivers to some sort of issue with the software you're using on your PC.


The good news is that if you want to fix this error, you can easily repair the various problems which first cause it to show by both updating the printer settings on your system and then repairing the various Windows settings which could be leading to the error. Here's how to do it...

The first step to fixing this runtime 482 printer error is to stop using "PrintForm" in any software that you're using. This is mainly for developers, as the "PrintForm" command is a code-level operation which can be called by the developer. Unfortunately, many Windows programs use this command incorrectly - leading your computer to be unable to read the files and settings it requires to run. If you want to resolve the error, you should either re-install the program that's causing the problem or update it with a new version.

The second step to fixing the runtime 482 error is to repair your computer's registry settings.

These are all stored in a big database on your PC, and basically keep your system running as smoothly as possible by helping Windows recall the various files and settings it needs to run. If you're seeing the 482 error on your PC, it could be caused by a poor set of data inside the registry, which can be fixed quite easily by using a "registry cleaner" tool to fix the problems your Pc has. Doing this should resolve the error completely for you.

Article Source: http://technology.ezinemark.com/how-to-fix-runtime-error-482-printer-error-steps-to-repair-the-482-error-on-your-pc-16949f93656.html

Read More

Printer Error 49 Fix - How To Repair The 49 Error With Your HP Printer

Printer Error 49 usually appears when you are attempting to print a document using a HP printer and then a communication failure error occurs between the computer and the printer. However, there are other probable causes for this message with an error 49 code to appear. There is a chance that it is related to the file that is being printed, or it could be due to a firmware problem. You must determine the cause of the problem and then fix the error to be able to make use of your printer again. This tutorial will guide you how to resolve printer error 49 on HP printers.
HP printer error 49 is typically caused by invalid print commands, damaged or corrupted data, invalid operations or sometimes registry issues. Some problems that can be easily fixed are caused by poor quality of the parallel cables that connect the printer to the computer. To stop the error messages from appearing, you must make sure that all possible causes are ruled out.
The way to fix HP printer error 49 is to first calibrate the printer. You can calibrate your printer by performing all these steps:

• Clear the print job from memory by pressing the Cancel Job command.
• Restart the printer by turning it off and on again.
• Print another job and this time from a different program.
• If the job printing was successful, return to the first application and print another file.
• If the error message shows up only with a specific software program or print job, contact the software vendor to get assistance from them.
• If the error message persists even with a different software application and print job, take off all the cables that connect the printer to the PC or the network and then turn off the printer.
• Open the printer and remove the entire set of memory DIMMS or third party DIMMS, but, DO NOT remove the firmware DIMM inserted in slot J1.
• Also, remove all the EIO devices from the computer.
• Turn on the printer again.
• If the error message does not appear again, then one by one return each of the DIMMS and EIO devices and turn the printer on and off each time you install a device.
• If you have pinpointed a specific device, replace it.
• Reconnect all the cables to hook the printer back up again to the computer or network.
• If the error code 49 still persists, replace the DIMM firmware.
• Lastly, replace the formatter of the printer and then calibrate the printer again.

After calibrating your HP printer, you have to make sure that your Windows registry is free from errors. The registry is an important component of Windows that stores all file and program settings that allow your operating system remember to load and use the different programs on your PC. Despite its significance in your system, it can be affected by the constant use it inevitably undergoes. You need to resolve registry issues by using a reliable registry cleaner that can thoroughly clean your registry. We highly recommend that you make use of "Frontline Registry Cleaner", which can resolve 99% of system faults found in your system, allowing you to use your computer in its optimal condition.

Article Source: http://EzineArticles.com/5641707

Read More

A Thorough Guide to Fixing That Printer That is Not Working

When your printer is not working, workflow can be seriously interrupted. Most PC users are dependent on printers to create important documents that are indispensable. As a result, a malfunctioning printer can cause all sorts of problems.

However, you can repair your printer with relative ease if you follow a few simple steps. Let's go over common printer error symptoms and how you can fix a broken printer.

Repairing The Print Spooler

One of the most common errors is related to the print spooler. The print spooler is a very important component that stores data on your print logs. In other words, the print spooler saves all assigned print jobs so that you can print things sequentially.

If it takes a ridiculously long time to print a document, or you see error messages related to the print spooler, then you need to take proactive steps to repair the print spooler. This does require restarting your computer and then making adjustments to the Print Spooler service. We can go over these basics here.

    You'll need to access Administrative Tools, so click "Start."
    Go to "Control Panel."
    Open "System and Maintenance."
    Then, open "Administrative Tools."
    Open "Services."
    Then, right-click on the service labeled "Print Spooler."
    Click "Properties."
    Select the tab labeled "General", and look next to the "Startup type" box. Ensure that you've selected "Automatic."
    You might need to click "Service status", then "Start", then "OK", if the service isn't running already. Otherwise, you're done.

Attacking Common Printer Issues

This process should quickly resolve your issues related to the Print Spooler. If it doesn't then you may need to reinstall drivers and check your hardware. If your printer is only printing blurry or faded documents, that's a sure sign that you need to replace your ink or toner cartridges.

Normally, the print queue will display messages related to low ink and toner. You should check the Devices and Printers menu if you're dealing with poor output documents.

This menu will also inform you if the printer is out of paper, or if there's a paper jam. If you don't see any of these messages, but your printer still isn't working, then it's very likely that you need to replace your printer drivers.

Updating Printer Drivers

Outdated printing drivers make it impossible for your operating system to process print jobs. As a result, you need to update drivers rapidly. One easy way to update drivers is to use Windows Update.

Windows Update will apply automatic updates to your system. However, sometimes it doesn't replace printer drivers. You can also try manually installing drivers by visiting the printer manufacturer website and downloading drivers there.

Finally, it's possible to find strong driver update software to replace all of your old drivers. The right kind of driver update program will do all the work for you. In other words, it'll search your system for old drivers and then find the new ones. It will then do a complete installation of these new drivers.

Source: http://goo.gl/J0UAV

Read More