Printer Error 49 Fix

Printer Error 49 usually appears when you are attempting to print a document using a HP printer and then a communication failure error occurs between the computer and the printer. However, there are other probable causes for this message with an error 49 code to appear. There is a chance that it is related to the file that is being printed, or it could be due to a firmware problem. You must determine the cause of the problem and then fix the error to be able to make use of your printer again. This tutorial will guide you how to resolve printer error 49 on HP printers.

HP printer error 49 is typically caused by invalid print commands, damaged or corrupted data, invalid operations or sometimes registry issues. Some problems that can be easily fixed are caused by poor quality of the parallel cables that connect the printer to the computer. To stop the error messages from appearing, you must make sure that all possible causes are ruled out.

The way to fix HP printer error 49 is to first calibrate the printer. You can calibrate your printer by performing all these steps:

• Clear the print job from memory by pressing the Cancel Job command.
• Restart the printer by turning it off and on again.
• Print another job and this time from a different program.
• If the job printing was successful, return to the first application and print another file.
• If the error message shows up only with a specific software program or print job, contact the software vendor to get assistance from them.
• If the error message persists even with a different software application and print job, take off all the cables that connect the printer to the PC or the network and then turn off the printer.
• Open the printer and remove the entire set of memory DIMMS or third party DIMMS, but, DO NOT remove the firmware DIMM inserted in slot J1.
• Also, remove all the EIO devices from the computer.
• Turn on the printer again.
• If the error message does not appear again, then one by one return each of the DIMMS and EIO devices and turn the printer on and off each time you install a device.
• If you have pinpointed a specific device, replace it.
• Reconnect all the cables to hook the printer back up again to the computer or network.
• If the error code 49 still persists, replace the DIMM firmware.
• Lastly, replace the formatter of the printer and then calibrate the printer again.

After calibrating your HP printer, you have to make sure that your Windows registry is free from errors. The registry is an important component of Windows that stores all file and program settings that allow your operating system remember to load and use the different programs on your PC. Despite its significance in your system, it can be affected by the constant use it inevitably undergoes. You need to resolve registry issues by using a reliable registry cleaner that can thoroughly clean your registry. We highly recommend that you make use of "Frontline Registry Cleaner", which can resolve 99% of system faults found in your system, allowing you to use your computer in its optimal condition.

Source:- Ezinearticles.com

Read More

Fix Printer Spooler Error

Your about to print an important document that you need for work or school and as you hit that print button, a windows error that says "Operation could not be completed. The print spooler service is not running". What to do now? Well here are a couple tricks that will fix this problem.

Instructions

1. Click on Start then click on Run. In the dialog box type services.msc and click OK, this will bring the services window up. Scroll down to print spooler, of course just turning it on wont fix it but we do want to make sure that the start up type set to automatic. double click on the Print Spooler Service and set start up type to Automatic, then click OK.

2. Restart the machine. Then once the machine is back up reinstall the software that came with the printer. If you don't have it you can always go to the vendors website and download it.

3. If that doesn't fix the problem we are going to want to completely uninstall all the software for the printer and reinstall it. So click on Start then Run type Control Panel in the dialog box and click OK. Click on add remove programs and uninstall the software for the printer.

Then check Under the Printer and Fax to see if it was uninstalled. If not then just delete it. Printer and Fax is in the Control Panel. Once it is completely uninstalled reinstall the software for the printer.

4. Then check Under the Printer and Fax to see if it was uninstalled. If not then just delete it. Printer and Fax is in the Control Panel.

Read more: eHow.com

Read More

Fix Lexmark Printer Errors

If your Lexmark inkjet or laser printer is printing erratically, printing incorrect colors or not functioning at all, you don't need to return the unit or find a service center for a repair immediately. There are a series of simple troubleshooting steps you can follow at home to fix the printer on your own.

Instructions

1. Check to make sure the printer's AC adapter is firmly plugged into a wall outlet and its USB cable is connected to the USB port on your computer. Try plugging the AC adapter into a different wall outlet, in case your outlet has stopped working or try a different USB cable in the event that it has gone bad. Pop open the top cover of the printer and check to see if any paper is jammed inside and needs to be physically removed.

2. Open the plastic cover over the ink cartridges or laser toner and pull them out. Check the orientation of the ink or toner. Replace them to make sure they are properly installed. Snap the plastic cover back into place.

3. Read the information on the LCD screen that shows the printer's status if you have a Lexmark laser printer. Check to see if there is a specific error message being displayed and then consult your manual to see what steps can be taken to fix the problem. Take the printer to a Lexmark authorized service center or purchase your own maintenance kit and replace the print head if you see the error message "Error 80 Scheduled Maintenance" (see Resources below). Remove and then return the toner cartridge if you see the error message "Error 20." Replace the cartridge entirely if you see the error message "Error 31," which indicates a defective cartridge.

4. Power your computer off and then back on. Attempt to print your document again in case your computer stopped recognizing your printer temporarily. Click "Start" on your task bar and then access the Control Panel. Choose the option to "Remove Programs." Uninstall the Lexmark software you installed when you first setup your printer. Locate the CD or floppy disk that came with your printer and put it in your computer. Follow the instructions on the screen to re-install the software.

5. Access the Control Panel again. Click "Printers." Verify that your Lexmark printer is in the list of available printers. Click "Add a Printer" if your printer is not showing up. Follow the instructions to add your printer. Navigate back to the Control Panel and click "Devices." Click on the plus sign next to "Printer" and then right-click on the name of your printer. Click "Settings" and then click "Drivers." Download the new software if a more up-to-date driver is available.

6. Open the Lexmark printer software by double-clicking on its desktop icon or navigating to it through the Start bar. Click on the option to print a test alignment page to ensure that your printer is now working properly.


Read more: eHow.com

Read More

Fix 0x0000007E Printer Error

SYMPTOMS
After you upgrade your computer to Windows XP, you might receive the following S...
After you upgrade your computer to Windows XP, you might receive the following Stop error message when the computer starts:
STOP: 0x0000007E (0xC0000005, 0x804E518E, 0xFC938104, 0xFC937E04)
SYSTEM_THREAD_EXCEPTION_NOT_HANDLED

WUSB54GCx86.sys- Address 92D89498 base at 92D7c000, Datestamp 45c04cc9
Note The parameters and file names in this error message might vary, depending on the cause of the Stop error. The file name in the second line of the error message, WUSB54GCx86.sys, is an example of a driver file that might be causing the error.

This article discusses seven methods for resolving the problem. The first method is designed for beginning to intermediate computer users. The other six methods are designed for advanced computer users.

Because this article contains steps that involve restarting your computer, you might find it easier to follow the steps if you print this article first.

CAUSE
This issue might occur if a system thread generates an exception that the error...
This issue might occur if a system thread generates an exception that the error handler does not catch. This exception can be caused by any of the following:

* If this issue occurs after the first restart during Windows Setup or after Setup is complete, the computer might not have sufficient hard disk space to run Windows XP.
* The computer BIOS might be incompatible with Windows XP, or it might have to be updated.
* The video adapter drivers might be incompatible with Windows XP.
* A device driver or a system service might be damaged.
* If the issue is associated with the Win32k.sys file, it might be caused by a third-party remote control program.


RESOLUTION
Use the Windows Error Reporting tool You can use the Windows Error Reporting to...
Use the Windows Error Reporting tool
You can use the Windows Error Reporting tool to send information about the error to us and to obtain information about any available fix or workaround. Follow these steps to use the Windows Error Reporting Tool:

1. When the Windows Error Reporting window pops up on your computer, click Send Error Report to send the error report to us.
2. In the confirmation window that appears after you send the error report to us, click More Information. This helps you find any available fixes for the problem or information about how to work around the issue.
3. If a fix or a workaround is not available, you can use the "Advanced Troubleshooting" section to try to resolve this issue. If you are not comfortable with advanced troubleshooting, you might want to contact Support. For information about how to contact Support, visit the following Microsoft Web site:
http://support.microsoft.com/contactus/ (http://support.microsoft.com/contactus/)


Advanced troubleshooting
Use the following methods in the order in which they are presented.

Method 1: Make sure that you have sufficient hard disk space
First, make sure that you have sufficient hard disk space. The Stop error can be caused by insufficient hard disk space.

If you can use safe mode or the Recovery Console to start the computer, delete any unnecessary temporary files, Internet cache files, program backup files, and files that contain saved file fragments from disk scans (.chk files). You can also install Windows XP on another hard disk that has more free space.

If you cannot start the computer, go to the next method to update the computer BIOS.

For more information about safe mode or the Recovery Console, click the following article numbers to view the articles in the Microsoft Knowledge Base:
315222 (http://support.microsoft.com/kb/315222/ ) A description of the Safe Boot Mode options in Windows XP
314058 (http://support.microsoft.com/kb/314058/ ) Description of the Windows XP Recovery Console

Method 2: Update the computer BIOS
If freeing space on your hard disk did not resolve the problem, the BIOS might have to be updated. Use the hardware and software vendor contact information articles that are listed in the "References" section to contact the computer manufacturer to obtain the most recent BIOS update.

Note When you update the BIOS, you might have to disable BIOS memory options, such as caching or shadowing, temporarily.
Method 3: Disable or update device drivers
If you have updated the BIOS successfully and the problem persists, the video adapter drivers on the computer might have to be updated or disabled. Follow these steps to troubleshoot the video adapter drivers:

1. If a driver is listed by name in the Stop error message, disable or remove that driver.
* If the error occurs during the startup sequence and the system partition uses the NTFS file system, you might be able to use safe mode to rename or to delete the faulty driver.
* If the driver is used as part of the system startup process in safe mode, you must use the Recovery Console to start the computer.
2. If the Stop error message does not indicate a specific driver, update the video adapter drivers to the latest versions.
3. Disable or remove any drivers or services that you recently added.
4. Check the Microsoft Hardware Compatibility List (HCL) to determine whether the PCI devices in the computer are compatible with Windows XP. For information about the HCL, visit the following Microsoft Web site:
http://www.microsoft.com/whdc/hcl/default.mspx (http://www.microsoft.com/whdc/hcl/default.mspx)

Method 4: Remove unsigned drivers
If you have updated the video adapter drivers and the problem persists, or if you cannot start Windows in safe mode, the problem might be caused by a different, unsigned driver. Remove all drivers that are not digitally signed by Microsoft. For more information about how to do this, click the following article number to view the article in the Microsoft Knowledge Base:
316434 (http://support.microsoft.com/kb/316434/ ) How to perform advanced clean-boot troubleshooting in Windows XP

Method 5: Remove all third-party drivers
You might be unable to determine which third-party driver causes the error. If removing unsigned drivers does not resolve the issue, try moving all third-party driver files from the %Windir%\System32\Drivers folder to a different location. Follow these steps to move the third-party driver files:

1. Use the Recovery Console to start the computer, or start the computer from a different installation of Windows if you have performed a parallel Windows installation.
2. Create a temporary folder to hold the driver files. For example, you could create c:\DriverTemp.
3. Move all files that do not have a creation date for Windows XP of 8/13/2001 from the %Windir%\System32\Drivers folder into the temporary folder that you created in step 2.

Caution If the computer relies on third-party IDE or SCSI controller drivers for correct operation, you must identify those driver files and then leave them in the %Windir%\System32\Drivers folder.
4. Restart the computer.
5. Continue the Windows Setup program. You can add the driver files back to the computer one at a time to identify the faulty driver.

Method 6: Remove third-party remote control services

If you still have the problem after you use the previous methods and the Stop error message contains the Win32k.sys file name instead of a driver file name, the problem might be caused by a third-party remote control program. To remove the service, use the Recovery Console to start the computer and then delete the third-party remote control service file.



 Source:- support.microsoft.com

Read More